Skip to content
Boiler Hire CompanyGet a quote
Menu

Industrial Boiler Hire

Factories, process lines and large estates use hired packaged boilers to cover a breakdown, a shutdown or a plant change. The units come in set sizes up to the low megawatts and can be coupled for bigger loads.

Get a quote

What kind of industrial hire do you need?

Industrial jobs differ more than commercial ones. These are the usual starting points.

SituationWhat usually works
Space heating for a factory or warehouseA hot water boiler on the heating circuit; tall buildings need less per m³ than offices.
Process hot waterA hot water unit sized to the process load, often with a buffer vessel.
Process steamA steam boiler, which brings the pressure systems rules with it. See steam hire.
Load bigger than one unitTwo or more packaged boilers coupled together, which also gives you a standby.

Tell us the load if you know it, or the output of the plant you are covering. That is what the firm will size from.

Size it before you ask

Our calculator turns floor area, height and insulation into a rough load and the next standard hire size up. No prices, just the size.

Open the sizing calculator

Hire firms price per week, often with a one-week minimum, plus delivery, connection and fuel. How hire is priced.

Packaged and containerised units

Larger hire boilers usually arrive as packaged units: boiler, burner, pumps and controls built into one frame, a container or a trailer. Packaged hire boilers commonly run from around 300 kW up to about 2 MW, and fleets list sizes such as 375, 500, 1,250 and 1,500 kW. For bigger loads, units are coupled together.

Units of this size commonly need a three-phase 32 A supply for the burner and pumps. If there is no spare supply near where the unit will stand, say so early, because a generator then becomes part of the hire.

Fuel on site

Oil-fired units are popular on industrial sites because they need nothing but a fuel delivery. At business premises in England, an oil container over 200 litres needs secondary containment, a bund, that holds at least 110% of the tank (GOV.UK). Hire tanks are normally bunded already. Wales, Scotland and Northern Ireland have their own rules, which NetRegs sets out for Scotland and Northern Ireland.

Gas units need a supply big enough for the burner and a Gas Safe registered engineer with the right non-domestic categories to connect them.

Lifting, standing and access

A containerised boiler may need a crane to get it into a yard or on to a roof. Lifting operations are covered by LOLER, the 1998 lifting regulations, so the lift has to be planned by a competent person and carried out safely (HSE). The hire firm normally arranges this, but you will need to agree the route, the standing and any road closure.

Big plant and permits

Combustion plant with a rated thermal input from 1 MW to 50 MW is medium combustion plant, and the Environment Agency explains when it needs a permit (GOV.UK). If you are hiring at that scale, ask the hire firm how its units are covered before they arrive. It's very important to settle this before the start date rather than after.

Sources for this page

How the hire usually runs

  1. Load and survey

    The firm confirms the load, the fuel, the supply and where the units can stand.

  2. Lift and place

    Units are delivered, lifted if needed and set on a firm standing.

  3. Connect and commission

    Flow and return, fuel and power are connected and the units commissioned.

  4. Run, service, collect

    The firm services the units during the hire and removes them at the end.

Industrial Boiler Hire: common questions

What sizes of industrial boiler can be hired?

Packaged hire boilers commonly run from around 300 kW to about 2 MW, and fleets list sizes such as 375, 500, 1,250 and 1,500 kW. Bigger loads are met by coupling units together.

Does a hire boiler need a bunded fuel tank?

At business premises in England, any oil container over 200 litres needs a bund holding at least 110% of its contents (GOV.UK). Hire tanks are normally supplied bunded.

Do we need a permit for a large temporary boiler?

Plant with a rated thermal input from 1 to 50 MW counts as medium combustion plant, and the Environment Agency sets out when that needs a permit (GOV.UK). Ask the hire firm how its units are covered.

Can a hire boiler supply process hot water?

Yes. The firm will want to know the flow rate and temperature the process needs, as well as the peak load, so it can size the unit and any buffer vessel.

What power does a large hire boiler need?

Packaged units above about 300 kW commonly need a three-phase 32 A supply for the burner, pumps and controls. If no supply is available, the firm can usually add a generator.

Tell us what needs heating

We find a boiler hire firm that covers your site and give you their name before any of your details go to them. It costs you nothing.

What happens next

  1. We look for a hire firm that covers your postcode and the size of unit you need.
  2. We give you the firm's name first. Your details only go to them if you say yes.
  3. The firm checks the site, confirms the size and sends a written price.

Boiler Hire Company is an independent matching service, not a hire firm. If you hire through the firm we name, they pay us a fee; you pay us nothing.

Step 1 of 3
Where is the building?
Get a quote