Skip to content
Boiler Hire CompanyGet a quote
Menu
Lagged pipework, gauges and a walkway in an old industrial boiler house
80 kW to 1.5 MWpackaged hire sizesGas, oil, electricand steam unitsPriced per weekby each hire firm

Boiler Hire Company

Temporary heating, hot water and steam boilers for UK buildings and sites. Tell us what needs heating and we find the hire firm.

Get a quote

Know roughly what size you need

Most people asking for boiler hire don't know the kilowatts, and that's fine. If the old boiler is still there, its data plate tells you. If not, a rough figure from the building's size gets the conversation started.

Our boiler sizing calculator takes floor area, ceiling height and how well the building holds heat, then rounds up to the next standard hire size and tells you the supply that size usually needs.

On price, hire firms don't publish rate cards. You pay per week, often with a one-week minimum, plus delivery, connection and the fuel you burn. See how boiler hire is priced.

Example: a 1,000 m² office, 3 m ceilings, average insulation

Volume
3,000 m³
Inside / outside
21 °C / −3 °C
Rough heat load
65 kW
Next hire size up
80 kW
Open the sizing calculator

Four things to settle with any hire firm

Temporary plant is still real plant, and the same rules apply to it. These are the questions that save trouble later.

Who connects it?

Gas work must be done by someone on the Gas Safe Register. For a commercial building, check the engineer's card covers non-domestic work.

Is the tank bunded?

In England, an oil tank over 200 litres at a business needs a bund holding at least 110% of its contents.

Where is the written scheme?

A steam system can't be run without a written scheme of examination. For a hired unit, that sits with the hire firm.

How is it lifted in?

A crane lift is a lifting operation under LOLER, so it needs planning by a competent person and an agreed route.

How a temporary boiler goes in

The hire firm handles the work. It helps to know the order things happen in.

Lagged steam pipework beside a boiler in a tight, dim plant room
  1. Site visit. Plant room, standing, access, fuel and power are checked, and the size confirmed.
  2. Delivery. The unit arrives on a trailer or as a container, craned in where needed.
  3. Connection. Hoses go to the flow and return, fuel and power are connected, and the unit is commissioned.
  4. Off-hire. When your own plant is back, the unit is drained, disconnected and collected.
Schematic of a hire boiler outside a building, with flow and return hoses to connection points on the building's heating pipework, and an oil tank in a bundYour buildingPlant room(old boiler offor removed)Heating circuitValved connection pointsFlowReturnHire boilertrailer or packaged unitFlueOil units: tankinside a bundPower for burnerand pumps
How a temporary boiler is usually joined to a building. A schematic, not to scale; the hire firm designs the actual connection for your site.
A row of valves with red handwheels on industrial pipework

Hiring a boiler in London?

London jobs tend to throw up the hardest site questions: basement plant rooms, no yard, a narrow street outside and a borough to ask about the kerb.

Our London boiler hire page goes through what to sort out before a unit arrives in the capital.

Boiler hire questions

What size boiler do I need to hire?

The output on the plate of the boiler you are replacing is the best single guide. Without it, our sizing calculator gives a rough figure from the building's volume and insulation, rounded up to a standard hire size.

Who connects a temporary gas boiler?

A Gas Safe registered engineer. Anyone doing gas work for gain must be on the register (Gas Safety (Installation and Use) Regulations 1998, regulation 3), and for commercial plant the registration should cover non-domestic work.

Does an oil-fired hire boiler need a bunded tank?

At business premises in England, an oil container over 200 litres needs a bund holding at least 110% of what it stores (GOV.UK). Hire tanks normally come bunded.

Gas, oil or electric: which should I hire?

Gas suits sites with a big enough supply near the plant room. Oil needs only a bunded tank and deliveries, so it works almost anywhere. Electric suits small loads and hot water, as long as the supply can carry the unit's full output.

How is boiler hire priced?

Per week, often with a one-week minimum, plus delivery and collection, connection and commissioning, and the fuel you use. Firms do not publish rate cards. Our page on hire costs explains each part.

Is a hired steam boiler covered by pressure regulations?

Yes. Steam at any pressure falls under the Pressure Systems Safety Regulations 2000, and the system needs a written scheme of examination before it is used (HSE).

Tell us what needs heating

We find a boiler hire firm that covers your site and give you their name before any of your details go to them. It costs you nothing.

What happens next

  1. We look for a hire firm that covers your postcode and the size of unit you need.
  2. We give you the firm's name first. Your details only go to them if you say yes.
  3. The firm checks the site, confirms the size and sends a written price.

Boiler Hire Company is an independent matching service, not a hire firm. If you hire through the firm we name, they pay us a fee; you pay us nothing.

Step 1 of 3
Where is the building?
Get a quote